Difference between revisions of "Miscellaneous"
Jump to navigation
Jump to search
(Imported from TWiki by twiki2mediawiki.py) |
(Imported from TWiki by twiki2mediawiki.py) |
||
Line 3: | Line 3: | ||
* Easy panel access (modify some interior panels to allow quick easy access when required) |
* Easy panel access (modify some interior panels to allow quick easy access when required) |
||
* Dash wiring (Key, wiper, rain light and Dash2 menu control wiring needs to be completed) |
* Dash wiring (Key, wiper, rain light and Dash2 menu control wiring needs to be completed) |
||
− | * Fit wing mirror (we have the missing mirror now!) |
+ | * *Fit wing mirror (we have the missing mirror now!) |
− | * Fix crack in body panel above rear wheel |
+ | * *Fix crack in body panel above rear wheel |
− | * Organise safe place to store body panel while working on car for long periods! (i.e. In the front of the crate) |
+ | * *Organise safe place to store body panel while working on car for long periods! (i.e. In the front of the crate) |
* '''Secure Aux 12V battery''' |
* '''Secure Aux 12V battery''' |
||
− | * Slots in seats for harness |
+ | * *Slots in seats for harness |
* Replace low voltage EVision with new high voltage EVision 2. |
* Replace low voltage EVision with new high voltage EVision 2. |
||
− | * Check torque settings on axle and drivetrain (see [http://blog.greenstage.co.nz/2008/12/half-shafts-and-software-installed.html blog]!) |
+ | * *Check torque settings on axle and drivetrain (see [http://blog.greenstage.co.nz/2008/12/half-shafts-and-software-installed.html blog]!) |
− | * Silicone and tape pins in the axle |
+ | * *Silicone and tape pins in the axle |
− | * clutch back stop (to prevent over extension) |
+ | * *clutch back stop (to prevent over extension) |
* '''Wheel alignment''' needed |
* '''Wheel alignment''' needed |
||
* [[Radiator|Liquid]] to the radiator and cooling system |
* [[Radiator|Liquid]] to the radiator and cooling system |
Revision as of 22:31, 26 March 2011
This page is our TODO list for minor jobs. The Team will knock these off during scheduled windows of opportunity (where the vehicle is available to be worked on for such jobs).
- Easy panel access (modify some interior panels to allow quick easy access when required)
- Dash wiring (Key, wiper, rain light and Dash2 menu control wiring needs to be completed)
- *Fit wing mirror (we have the missing mirror now!)
- *Fix crack in body panel above rear wheel
- *Organise safe place to store body panel while working on car for long periods! (i.e. In the front of the crate)
- Secure Aux 12V battery
- *Slots in seats for harness
- Replace low voltage EVision with new high voltage EVision 2.
- *Check torque settings on axle and drivetrain (see blog!)
- *Silicone and tape pins in the axle
- *clutch back stop (to prevent over extension)
- Wheel alignment needed
- Liquid to the radiator and cooling system
- Replace the rear wheel nuts as well (for consistency with front - requires studs to be shortened or replaced)
- Gear leaver mechanical connection (Standard Saker setup needs to be modified due to chassis variations)
- Data logger (wiring for data logger and GPS needs to be completed - separate harness for this)
Done:
Padlocks*Front wheel spacers* Bruce says spacers not needed, machine the nuts to sort this out!(we have replaced the the wheel studs and nuts)Get clutch working (hydraulic line is not properly connected or bled)
-- Main.PhilipCourt - 25 Jan 2009